Author Topic: PCL: Comet Alignment module  (Read 40497 times)

Offline gvanhau

  • PixInsight Old Hand
  • ****
  • Posts: 343
    • View Profile
Re: PCL: Comet Alignment module
« Reply #30 on: 2012 October 03 19:47:03 »
Geert Vanhauwaert

Offline NKV

  • PTeam Member
  • PixInsight Guru
  • ****
  • Posts: 677
    • View Profile
Re: PCL: Comet Alignment module
« Reply #31 on: 2012 October 03 22:10:01 »
They are calibrated, registered and debayerd
Hi,
Problem in ImageRegistration. Blink  the images to see that image #099 is not registered to other two.

Best regards,
Nikolay.

Offline gvanhau

  • PixInsight Old Hand
  • ****
  • Posts: 343
    • View Profile
Re: PCL: Comet Alignment module
« Reply #32 on: 2012 October 05 05:35:21 »
Thanks Nikolay

I removed #99 from the process and it worked great.

Regards
Geert
Geert Vanhauwaert

Offline NKV

  • PTeam Member
  • PixInsight Guru
  • ****
  • Posts: 677
    • View Profile
Re: PCL: Comet Alignment module
« Reply #33 on: 2012 October 05 09:02:07 »
I removed #99 from the process and it worked great.
:)
If you have any idea for improvement the module - welcome.

Offline gvanhau

  • PixInsight Old Hand
  • ****
  • Posts: 343
    • View Profile
Re: PCL: Comet Alignment module
« Reply #34 on: 2012 October 05 19:00:34 »
Hello Nikolay

I have some trouble with the module.
When I save a project containing the module (process icon) I can not load the project anymore because it crashes PI.
I tried wit a project containing only this module as process icon.
Can you please verify this?

Regards
Geert
Geert Vanhauwaert

Offline NKV

  • PTeam Member
  • PixInsight Guru
  • ****
  • Posts: 677
    • View Profile
Re: PCL: Comet Alignment module
« Reply #35 on: 2012 October 05 21:21:53 »
When I save a project containing the module (process icon) I can not load the project anymore because it crashes PI.
Bug fixed.

v.1.0.2.0001 BugFix: process icon problem(impossible to load process icon) - fixed.

Offline gvanhau

  • PixInsight Old Hand
  • ****
  • Posts: 343
    • View Profile
Re: PCL: Comet Alignment module
« Reply #36 on: 2012 October 06 10:04:25 »
That worked ok, even with my previously saved project.
Thanks

Geert
Geert Vanhauwaert

Offline GrantBoxer

  • Newcomer
  • Posts: 42
    • View Profile
Re: PCL: Comet Alignment module
« Reply #37 on: 2012 October 14 05:19:14 »
Hi All, I am a newbie to PixInsight but I have collected about 20-odd images of comet P168 last night and am trying to process the images using the Comet Alignment Module. I note that it uses the Date-Obs field which is in the original image file, but as I have single shot colour QHY-8 when I debayer the images, the Date-Obs field plus all the other FITS camera data appears to be lost in the debayered header files. Have I missed something? Any suggestions? Cheers Grant

Offline NKV

  • PTeam Member
  • PixInsight Guru
  • ****
  • Posts: 677
    • View Profile
Re: PCL: Comet Alignment module
« Reply #38 on: 2012 October 14 07:08:39 »
when I debayer the images, the Date-Obs field plus all the other FITS camera data appears to be lost
There are problem in BatchDeBayer Script, which don't preserve FitsKeywords.

Use Debayer Module + Image Container. ;) That combination doing same, but preserve FitsKeywords.

Offline Flea77

  • Newcomer
  • Posts: 24
    • View Profile
Re: PCL: Comet Alignment module
« Reply #39 on: 2012 October 14 09:49:33 »
It seems I am a little slow. I have tried the CometAlignment tool and it seems to see the comet fine (I can select the comet in the first and last image, I can see the green circle move as I open other images as it should). I then select an output directory and click apply. It makes a series of fit files. If I open those fit files in BatchPreprocessing it does not seem to do any different than the raw files before using CometAlignment.

I know I am doing something stupid, can you point me in the right direction?

Allan

Offline NKV

  • PTeam Member
  • PixInsight Guru
  • ****
  • Posts: 677
    • View Profile
Re: PCL: Comet Alignment module
« Reply #40 on: 2012 October 15 00:09:38 »
I have tried the CometAlignment tool and it seems to see the comet fine (I can select the comet in the first and last image, I can see the green circle move as I open other images as it should). I then select an output directory and click apply. It makes a series of fit files. If I open those fit files in BatchPreprocessing it does not seem to do any different than the raw files before using CometAlignment.
Please check ( Menu>File>FitsHeader ) are really images was processed by Comet Alignment module. Open one image and check history in FitsHeader. Look my print screen for example.

Offline Solidarity

  • Member
  • *
  • Posts: 56
    • View Profile
Re: PCL: Comet Alignment module
« Reply #41 on: 2012 October 19 01:23:27 »
Hello Nicolay,

thanks for the great Comet Script. It works well!  :)

What do you think is the best integration algoritm after registration! I used Winzorized Sigma but I;m looking forward to your answer!

Greetings from Germany

Karsten

Offline NKV

  • PTeam Member
  • PixInsight Guru
  • ****
  • Posts: 677
    • View Profile
Re: PCL: Comet Alignment module
« Reply #42 on: 2012 October 19 11:54:03 »
best integration algoritm
Sorry, I have no idea.

Offline georg.viehoever

  • PTeam Member
  • PixInsight Jedi Master
  • ******
  • Posts: 2129
    • View Profile
Re: PCL: Comet Alignment module
« Reply #43 on: 2012 October 21 00:46:11 »
What do you think is the best integration algoritm after registration! I used Winzorized Sigma but I;m looking forward to your answer!
I think there are some hints in the documentation. I cannot check this right now... No access to PI here...
Georg (6 inch Newton, unmodified Canon EOS40D+80D, unguided EQ5 mount)

Offline georg.viehoever

  • PTeam Member
  • PixInsight Jedi Master
  • ******
  • Posts: 2129
    • View Profile
Georg (6 inch Newton, unmodified Canon EOS40D+80D, unguided EQ5 mount)