Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - llpastro

Pages: 1 [2] 3 4 ... 14
16
Bug Reports / Re: error in subframe selector
« on: 2019 January 23 12:28:25 »
I just installed the newest update and where SubframeSelector worked fine before, I now get this same error.  If I close it and reopen I get no error message but when I run the Measure Images, there is no data in the graph field.

Larry

17
General / Re: Inside Pixinsight - Second Edition Availibility
« on: 2018 December 31 07:26:02 »
I received the second copy of the book from Amazon which was printed in Middletown, DE (the first copy was printed in California) and it was not misassembled.  However, the issue with the index was still a problem.   Index page numbers do not agree with the actual subject page.  Springer is aware of the issue.

Larry

18
General / Re: Inside Pixinsight - Second Edition Availibility
« on: 2018 December 28 06:59:06 »
You are right.  I have had mine for almost a week and discovered mine had page sections misassembled but I did not look at the index.  Mine is incorrect also.  Mine came from Amazon and there is a replacement on the way due Sunday.  I will check it for both of those problems and report back.  I have the first addition and the new index does not fit the first book either.

Larry

19
General / Re: Inside Pixinsight - Second Edition Availibility
« on: 2018 December 26 06:28:56 »
I am the one that received the hard copy and not with standing the assembly problem, the print quality is much better.  Images have a slight gloss to them and show more detail.  Also the font size is a little bigger than the first book making it more readable.

Larry

20
Thanks Kayron, this is much needed.  I can see you put a lot of work into this tutorial.

Larry Phillips

21
A question has come up on another forum about whether this should be used on a linear image or a nonlinear image or does it matter?

Larry

22
General / Re: Inside PixInsight the Book
« on: 2018 October 25 07:35:40 »
The word I received is that it is delayed a little.  It is in the hands of the publisher to release.

Larry

23
General / Juan and Vicente
« on: 2018 August 22 07:44:59 »
Does anyone know what has happened to Juan and Vicente?  It has been quite a while since I have seen a posting by either of them.

Larry

24
Workshops and Conferences / Re: 3-Day Western USA Workshops
« on: 2018 May 26 07:53:43 »
What happened to Tucson?

Larry

25
Announcements / Re: New RAW Module - Ready for Testing
« on: 2018 February 10 06:09:41 »
I have searched but if you find it, post it here as I would love to use it.

Larry

26
Announcements / Re: New RAW Module - Ready for Testing
« on: 2018 February 08 14:53:37 »
Just as I thought.  The 80D only uses Dual Pixel for autofocusing, need the 5D to take DPR images.

Larry

27
Announcements / Re: New RAW Module - Ready for Testing
« on: 2018 February 08 06:08:21 »
I also have an 80D.  Correct me if I am wrong, but I was under the impression that Dual Pixel is only used for auto focus.  Comments above indicate that the camera can take DP images as an option.  Can someone enlighten me?

Larry

28
Image Processing Challenges / TheSkyX FITS Pedestal in Header
« on: 2017 December 10 06:45:58 »
Warren Keller, I decided to create a new thread for this topic as my reply was getting lost in the thread you have under Bug Reports regarding the -100 pedestal. Please refer to that thread for continuity.  I am using the manual calibration method and have the -100 value in the fits header for the pedestal.  For your solution, do I need to do the same to the darks?  And what about the biases themselves?  Do I need to do anything to them before I create a master bias?  Also, after rereading Juan's comments, he says to insert 100 as the bias value whereas you said 0.  Can either be used?

Larry

29
Warren, I am using the manual method.  Do I need to do the same to the darks?  And what about the biases themselves?  Do I need to do anything to them before I create a master bias?  Also, after rereading Juan's comments, he says to insert 100 as the bias value whereas you said 0.  Can either be used?

Larry

30
Thanks Warren.  I will see if I can reproduce that workflow.

Larry

Pages: 1 [2] 3 4 ... 14